Request A FREE Catalog

become a dealer
 

You're currently on:


Oil Pump Specifications

Type Pump, splash, gravity feed

Crankshaft Bearings Gravity feed

Connecting Rods Splash

Camshaft Bearings Gravity feed

Oil Pump Type Gear

Oil Pump Capacity 9 pints, minimum at 1300 rpm

Oil Pump Pressure 80-100 pounds

Oil Pump Shaft 1/2" diameter (in 5/8" bore), except 1928 with 9/16" bore & undercut shaft (Model B used 5/8" bore with undercut shaft)

Oil Pump Gear Teeth to Housing Clearance .001" to .002"

Housing Cover to Face of Gears Clearance .001" to .002"

Drive Gear to Camshaft Gear Clearance .003" to .005"

( Back to Top )

 

Transmission Specifications

Gear & Shaft Material Chromium alloy steel

Gear Ratios
High-1:1 (100%)
2nd-6.89:1 (53.8%)
Low-8.75:1 (32.04%)
Reverse-26.7%

Bearings
Main shaft front (ball) 1208;
Main shaft rear (ball) 1306

Transmission Case Length 6.560" to 6.565"

Case Front Bearing Hole 3.1497" to 3.1507" diameter

Case Rear Bearing Hole 2.835" to 2.836" diameter

( Back to Top )

 

Clutch Specifications

Material Molded asbestos composition

Pressure Plate Weight 15 pounds

Clutch Disc Weight 2-1/2 pounds

Pivot Pedal Pressure 30 pounds

Clutch Facings 9" diameter, 9/64" thick

Inside Diameter 5-3/4"

Total Acting Surface Area 75 square inches

Clutch Pedal Clearance 3/4" for multiple disc, 1" for single

Clutch Release Bearing Hub 2.065" diameter

Clutch Throw Out Bearing B7580 or B7580T

Clutch Pressure 1100 pounds

( Back to Top )

 

Radiator Specifications

1928 Manufacturer Ford

1929 Manufacturer Flintcock, Long, McCord

1930-31 Manufacturer Ford

 

Standard Radiators 1928-29

Tubes Flat 1/2" seamless

Number of Tubes 101 in 3 rows, staggered at 9/16" centers

Number of Fins 5 fins/inch-98 fins

Core Size 19-3/4" x 19-1/8" x 2-3/16" centers

1928-29 Heavy Duty 8 fins/inch-158 fins

 

Standard Radiators 1930-31

Tubes Flat 1/2" seamless

Number of Tubes 95 in 3 rows, staggered at 9/16" centers

Number of Fins 5 fins/inch-100 fins

Core Size 20-1/8" x 18" x 2-3/16" centers

1930-31 Heavy Duty 8 fins/inch-167 fins

( Back to Top )

 

Zenith Carburetor Specifications

Throat Size 1"

Float Level 5/8" below upper body machined surface. Model B, 33/64" below upper body machined surface.

Main Jet .037" ID (#63 drill bit)

Cap Jet .037" ID

Compensator Jet .035" ID (#65 drill bit)

Idling Jet .021" ID (#75 drill bit)

( Back to Top )

 

How to Tell if You Have a Zenith or a Tillotson Carburetor?

It’s easy. The original Zenith carburetors had round-shaped cast iron bodies, while Tillotson carburetors were made of an aluminum alloy, with more of a “boxy” shape. Usually, Zenith carburetors are found painted black, while Tillotsons are normally unpainted aluminum color.

( Back to Top )

 

Water Pump Specifications

Water Pump Shaft 5/8" diameter
Water Pump Shaft End Play .006" to .010"
Radiator Hose
Upper: 2" diameter, 6-1/4" long (28-29) 8" long (30-31).
Lower: (2 pieces) 1-3/4" diameter,
2-3/4" long.

( Back to Top )

 

Fan Blade & Belt Specifications

Fan Belt Width 5/8"

Fan Belt Length 42-7/8"

Fan Cooling Surface 374 square inches

Fan Speed 1-1/2 times engine rpm. Fan delivers about 855 cfm at 1,000 rpm, about 24 mph

4 Blade Fan At 1,000 rpm, 62% increase in air flow,
82% increase in HP absorbed; at 2,000
rpm, 55% increase in air flow, 47%
increase in HP absorbed.

( Back to Top )

 

Gas Tank Specifications

Steel Thickness .049" to .051" (terne plated)
Capacity 28-29: 10 gallons 30-31: 11 gallons

( Back to Top )

 

Generator Specifications

Type Two pole

Voltage Regulation Fixed control

Brushes 3 (1 adjustable)

Armature Bearings
29-Mid ’30: Ball front & rear
After Mid 30: Ball front, bushing rear

Armature Speed 1-1/2 of engine speed

Armature Length 28-April ’30: 7-9/16" - uses 1-5/32" wide pulley
after April 30: 7-21/32" - uses 7/8" wide pulley

Max. Normal Charging Rate 12 amps @ armature 1600 rpm (25mph)

Cutout Closes Approximately 9 mph

Cutout Opens Approximately 8 mph

Contact Gap .015" to .020"

Core Gap .010" (contacts closed)

Brush Spring Tension 25 to 40 ounces each

Field Coils 100 turns of #17 copper wire

Armature 14 coils with 6 turns of #17 copper wire

Commutator 28 copper segments

Field Current Draw 6.3 amps at 7 volts, generator
(motoring draws 5.75 amps at 7 volts)

Maximum Current 18 to 22 amps at 6 volts

Motoring Freely 5 amps at 6 volts

Field Test 5.2 amps at 6 volts

The very earliest Model A Fords were equipped with “Powerhouse” generators (shown below), which had a pancake shape & a body covered with sheet metal. Soon Ford replaced them with the more familiar generator that is shown below. These generators, when working properly, are simple, durable & reliable.

Photo Captions:
1. Cut-Out
2. Cover band
3. Pulley
4. Rear End Plate

( Back to Top )

 

Battery Specifications

Terminal Grounded Positive

Voltage 6 volt

Capacity 80 amp hours, starting capacity 98 amps

Number of Cells 3

Number of Plates 13 per cell

Charging Rate 10 to 12 amps

( Back to Top )

 

Starter Motor Specifications

Type of Drive Bendix (except early 1928)

Terminal Grounded Positive

Rotation Counterclockwise (viewed from commutator or bushing end)

Armature 21 segments

Brush spring 35 to 40 ounces

Data Torque RPM Volts Amps
Normal 3 1500 5 175
Running Free - 4000 6 50
Locked 15 0 3.2 550
Test Data 4 1000 4.85 225
  8 540 4.15 360
  12 220 3.60 475
( Back to Top )

 

Distributor Assembly Specifications

Rotor Revolution Direction Counterclockwise

Point Gap .018" to .022"

Point Spring Tension 16 to 18 oz.

Condenser Capacity .20 to .25 mfd

Yellow Wire Ignition Circuit 12 gauge

All Other Wiring (except high tension circuit) 16 gauge

Camshaft to Bearing Clearance .001" to .002"

Spark Control Manual Advance 20° (28° camshaft travel)

Rotor End Cap to Distributor Terminal .020"

Ignition Circuit .62 amps at 6.2 volts (engine at 1500 rpm)
4 amps at 6.2 volts (engine stopped)

Set point gap at .018"-.022" (.022" for new points). The rubbing block on the points will wear down .003"-.005" after approximately 400-1,000 miles. After this point, wear might only be .001" over the next 10,000 miles. Therefore, be sure to reset the point opening to .022" by the end of the first 1,000 miles.
( Back to Top )

 

Spark Plug Specifications

Spark Plugs Champion 3X, 7/8" x 18 thread

Spark Plug Gap
.035" (A6050A cylinder head),
.030" (B6050 cylinder head),
.025" (A6050B cylinder head)

( Back to Top )

 

Interior Lights Specifications

Instrument Panel 3 candle power, single contact, B13466

Dome 3 candle power, single contact, B13466

Commercial Dome 21 candle power, single contact, B13465


( Back to Top )

 

Wiring Books

Manual ELECTRICAL WIRING DIAGRAM   Manual ELECTRICAL WIRING DIAGRAM   
Year: 1928-1931
Part #: A14000/1
$7.50
More Info Buy Now


Manual ELECTRICAL WIRING DIAGRAM   Manual ELECTRICAL WIRING DIAGRAM   
Year: 1928-1931
Part #: A14000/2
$7.50
More Info Buy Now


( Back to Top )

 

Cylinder Block Specifications

Length 19-5/16"

Width 7-13/16"

Height 11-1/2"

Bore 3.875" to 3.876"

Bottom of Block to Camshaft Centerline 2.876" to 2.878"

Top of Block to Camshaft Bore Centerline 8.624" to 8.627"

Valve Lifter & Guide Bore .594" to .5945" diameter

Distributor Drive Gear Bore .9365" to .9375" diameter

Cylinder Outside Diameter 4-3/8" outside diameter

Flatness of Top of Block .003" to .005"

Cylinder Bore Perpendicular
to the Top of the Block
.001" to .002"

( Back to Top )

 

Windshield Wiper Information

From the start of production, the Model A was equipped with windshield wipers. Early wipers were either manual (commercial & open car) or electric (closed car). All ’28 electric wipers were made by the Owen-Dyneto Company, who used zinc die-castings (also known as pot metal) for the base, cover & levers. This was a very brittle metal that broke & warped over the years, leaving very few intact wipers.

Beginning in February ’29, Ford began using electric wipers from Heinz Electric Company & in March ’29 from E.A. Laboratories, Inc. These new wipers were made from pressed steel & were much more durable.

( Back to Top )

 

General Sheet Metal Information

When faced with rusted or missing Model A sheet metal, yesterday’s restorer had to rely on used metal panels & body parts from a dry climate, or hand-made panels hammered out by highly talented metalsmiths.

But today, MAC's Antique Auto Parts is proud to offer a tremendous selection of precision-crafted sheet metal panels & components for many different Model A body styles. Like the original panels, MAC's sheet metal parts are die stamped from heavy gauge steel, with correct flanges, contours & seams as original. You’ll like working with new solid steel instead of thin & rust-weakened panels full of body filler.

As with any new body part, these panels might require some fitting & minor metal work & must be welded by a competent body person. Return that new-steel “solid” feeling to your Model A with brand new steel sheet metal parts & panels from MAC's!

( Back to Top )

 

Hood Specifications

( Back to Top )

 

MAC's DISCLAIMER:

The content MAC's presents on its "Vehicle Identification & Specification" pages & in its catalogs is for information use only and is intended to be used as a guide. While MAC's makes every effort to ensure accurate content, occasionally errors may occur. MAC's does not take responsibility & will not be held liable for any automotive parts purchases, repairs or restoration decisions made as a result of information presented here or anywhere in its catalogs.

 

Page One